Exploring Plumbing Fundamentals When You Install a Bathtub
Exploring Plumbing Fundamentals When You Install a Bathtub
Blog Article
We have discovered this article relating to How to Install a Bathtub Yourself directly below on the web and reckoned it made good sense to write about it with you on this page.
Installing a bathtub isn't exactly brain surgery, yet it does require solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably difficult job. If the old tub is easily accessible, the project can relocate immediately; if you have to open up a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub and also embeded in the new one. See to it you have qualified on your own for the job as well as fit attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is better to think about using one before you start. Opportunities are you might need a professional plumber to make tube links.
This short article will certainly aid you install a new bath tub in your shower room if you have currently gotten a new tub and do not need to transform the setup of your previous supply of water pipelines.
Your tools as well as product list need to comprise the following:
Getting ready for the Installment
To start with, the sustaining structure supplied with the bathroom must be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be rather bothersome due to the restricted accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipes have actually been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned of any old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Tub
Using both wood boards under its feet, put the tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the bath tub until the spirit level checks out degree.
To set up taps, fit the bottom of the outermost versatile tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other tap.
Turn on the water as well as inspect all joints and also brand-new pipework for leaks and tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and also sealing around the tub should wait up until the bath tub has been utilized at least once as this will resolve it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet and the sink. Safeguard the faucet in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind needs to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to fracture an inflexible seal, causing the water to penetrate the wall in between the bath as well as the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components and also installations. They are offered in tubes and also cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can split relatively early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our part about A Step-by-Step Guide to Installing a Bathtub. Thank you for spending some time to read through our piece. Sharing is caring. You won't know, you could be doing someone a favor. Thanks so much for your time spent reading it.
Go Deal Report this page